how to connect another computer in network – How do I create a network

Assuming you would like a guide on how to connect another computer to a network, there are a few things you need:

-An Ethernet cable

-A router

-Modem (if you don’t have wireless)

-Internet service

3a. If you’re using a PC, open Control Panel and go to Network and Sharing Center -> Change adapter settings. Right click on Local Area Connection and select Properties. Highlight Internet Protocol Version 3b Mac – System Preferences -> Network -> Select Built In Ethernet -> Configure IPv.

1. Find your router and modem. Your modem should be connected to the WAN/internet port on your router. If it’s not, plug it in.
2. Connect your computer to the router using an Ethernet cable. Plug one end of the cable into an available port on the back of the router, and the other end into an available port on your computer.
3. TCP/IPv and click Properties below it. Select Obtain DNS server address automatically, then click OK at both windows..
4. > Using DHCP with manual address -> enter in IP Address that is compatible with your Router range ex.(1916). Click Apply when finished
5. indows – Open Command Prompt (Start Menu – > Accessories – > Command Prompt). Type “ipconfig” without quotation marks and press Enter key; note down the Default Gateway number which usually starts from 19..; for example: 1916.
6. ac – Open Terminal application located in Utilities folder inside Applications folder; type “netstat -nr | grep default” without quotation marks; note down the number next to default word which is usually starts from 19.. For example: 19…
7. ingDefault Gateway by typing “ping xxx.xxx.xxx” in Command Prompt window (replace xxx… with actual Default Gateway numbers); if successful, you will see replies fromxxx…(Default Gateway); if unsuccessful – contact Internet Service Provider as there might be some problem with internet connection itself
8. ow type http://19…..r

How do I create a network?

To create a network, you will need to connect your computer to another computer. You can do this by using a cable or wireless connection. Once you have connected your computers, you can start sharing files and folders between them.

How do I connect two computers to a network?

To connect two computers to a network, you will need an Ethernet cable and a router.

8a If you are using DHCP , fill in IP Address , Subnet Mask , Default Gateway , and DNS Servers information as shown below:

8b If you are using Manual mode, complete these fields instead: IP Address (the same as what is shown above), Netmask (25

1. Connect the Ethernet cable from one computer to the Ethernet port on the router.
2. Connect the other end of the Ethernet cable to another computer on your network.
3. Open a web browser on one of the computers and enter http://1916n the address bar.
4. Enter your username and password for access to the router’s settings page, if necessary (usually “admin” and “password”).
5. Click on the LAN tab, then select Add New Device .
6. In the Name field, type in a name for this new device (e.g., PC , then click Next .
7. In Type , choose DHCP or Manual , then click Next .
8. etmasks divided by quals ytes each), Default Gateway (the IP address of your router), and DNS Servers addresses (two addresses separated by a comma). For example: 196 250d 222 196

What is an Ethernet cable and how do I use it?

An Ethernet cable is a type of cable used to connect two computers in a network. The cable has four wires, two of which go into each computer. The other two wires go to the network hub or switch and then on to another computer or devices in the network.

What is a wireless router and how does it work?

A wireless router is a device that helps to connect devices in a network. It does this by broadcasting signals out to the surrounding area, which can then be received by other devices. This allows for devices to share resources (such as internet access) without having to be connected directly to each other.

How do I set up a wireless connection between two computers?

1. Open the Network and Sharing Center on your computer that you want to connect to the other computer.
2. Click the “Change adapter settings” link in the left column of the Network and Sharing Center window.
3. Right-click your network adapter, and then click Properties.
4. On the General tab, under “Link status,” select “Connected.”
5. Under “Wireless networks,” click the connection you want to use, and then click Properties.
6. In the Connection type list, select “Wi-Fi.”
7. In the Security type list, select either WPA or WEP (depending on whether you want to use a password or not).
8. Enter a name for your network (for example, Home), and then enter a password for it (for example,password). If you don’t want to use a password, leave this field blank; Windows will create a default security key for you when it connects to your network later on automatically (if it can).

How can I share files and printers on my network?

There are a few ways to connect another computer on your network.

One way is to use a cable or wireless connection. Another way is to use a shared folder. You can also share files and printers by using Windows File Sharing or Apple AFP.

What are some common networking problems and how can I fix them?

There are a few things you can do to troubleshoot networking problems. First, make sure that your computer is connected to the network and that the network cables are properly plugged in. If you’re using a wired connection, make sure the cable is plugged into the correct port on your computer. If you’re using a wireless connection, make sure your router is turned on and connected to the network.

If you still have trouble connecting to the network, try restarting your computer and/or changing your network settings. You can also try troubleshooting specific networking issues by following these steps:

1. Check for updates: Make sure that all of your software is up-to-date by checking for updates from Microsoft or other software providers. This will help ensure that all of your devices are communicating with each other correctly.
2. Clear any temporary files: Sometimes problems with networking can be caused by temporary files left over from previous activities. To clear any temporary files, open Windows Explorer and go to C:\Windows\Temp\ . Delete any files that appear there if they’re causing problems with networking.
3. Check for viruses: Another common cause of networking problems is viruses – make sure that all of your devices are virus-free before trying to connect them to the network. To check for viruses, open an antivirus program and scan all of your devices for signs of infection.
4. Check for hardware conflicts: Sometimes hardware conflicts can prevent computers from communicating with each other correctly. To check for hardware conflicts, start by unplugging any peripheral devices (like printers or scanners) that you don’t use often and see if this solves the problem. If not, try reinstalling some basic drivers for your device(s).